爱泽工业2018年5月部分到货产品专题及库存——FAAC/NICE门电机篇新闻中心上海爱泽工业设备有限公司

您好！欢迎光临工博士智能制造网！平台热线：021-80392549

上海爱泽工业设备有限公司

工业控制领域内相关产品的代理分销及技术服务

1

产品分类

新闻中心

爱泽工业2018年5月部分到货产品专题及库存——FAAC/NICE门电机篇

发布时间：2018-05-18 浏览次数：92 返回列表

爱泽工业2018年5月部分到货产品专题及库存

——FAAC/NICE门电机篇

如下为我司爱泽工业IZE_Industries本月部分到货FAAC/NICE电机相关产品，欢迎来电索取样本资料和产品信息。

FAAC门电机C850爱泽工业izeindustries NICE门电机BM5024爱泽工业izeindustries

FAAC门电机C850描述及技术规格

General

These instruction apply to the following models: C850

The C850 is an electromechanical operator designed for moving sliding gates.

The non-reversing system is guaranteed by an electric brake that prevents manual movement of the sliding leaf when the motor is stopped, and therefore does not require an electric lock.

A handy manual release makes it possible to manoeuvre the gate in case of black-out or operator inefficiency

C850是一款专为移动滑动门而设计的机电操作器。

非反转系统由电动制动器保证，防止电机停止时滑动叶片的手动移动，因此不需要电锁。

非换向系统由电动制动器保证，当电机停止时，可防止滑动叶片的手动运动，因此不需要电动锁。

便捷的手动释放装置可以在停电或操作效率低的情况下操纵门。

FAAC门电机C850规格大小

Installing the automated system

Preliminary checks

For the safety and correct operation of the automated system, ensure that the following conditions are met:

• The gate structure must be designed to be automated. In particular, the diameter of the wheels must conform to the weight of the gate being automated, there must be a guide on top and mechanical limit switches sized to suit the weight and speed of the movable leaf, to avoid derailment of the gate;

• Initially, leave at least 10 cm of clearance between the movable leaf stopping points (open and close) and the mechanical stops of the gate. The final adjustment is made once the inverter programming precedure is completed. Minimum distance 3 cm.

• The gate sliding rail must be linear and horizontal.

• Manual movement of the gate must be smooth along the entire stroke.

• The characteristics of the ground must guarantee sufficient solidity of the foundation plinth.

• No tubes or electrical cables should be present in the plinth digging area.

• If the gear motor is exposed to vehicle transite, provide for adequate protection against accidental impact, when possible.

• Ensure that there is an efficient earth plate for connecting the gearmotor.

Should various elements not need the above-mentioned conditions, adjust them so they do.

安装自动化系统

初始检查

为确保自动化系统的安全和正确运行，请确保满足以下条件：

•门结构必须设计为自动化。特别是车轮的直径必须符合自动门的重量，在顶部和机械限位开关上必须有一个导向装置，以适应活动门叶片的重量和速度，以避免门脱轨;

•最初，在可移动的叶节点（开启和关闭）和门的机械停止点之间留出至少10厘米的间隙。最终调整是在逆变器编程之前完成的，最小距离3厘米。